dual-in-line sockets solderless press-fit open frame www.mill-max.com 516-922-6000 19 series 104 10 0.5 0.2 0.3 40 104-13-210-41-770 104-13-210-41-780 4 0.2 0.3 0.4 102 104-13-304-41-770 104-13-304-41-780 6 0.3 0.3 0.4 67 104-13-306-41-770 104-13-306-41-780 8 0.4 0.3 0.4 50 104-13-308-41-770 104-13-308-41-780 10 0.5 0.3 0.4 40 104-13-310-41-770 104-13-310-41-780 14 0.7 0.3 0.4 28 104-13-314-41-770 104-13-314-41-780 16 0.8 0.3 0.4 25 104-13-316-41-770 104-13-316-41-780 18 0.9 0.3 0.4 22 104-13-318-41-770 104-13-318-41-780 20 1.0 0.3 0.4 20 104-13-320-41-770 104-13-320-41-780 22 1.1 0.3 0.4 18 104-13-322-41-770 104-13-322-41-780 24 1.2 0.3 0.4 16 104-13-324-41-770 104-13-324-41-780 28 1.4 0.3 0.4 14 104-13-328-41-770 104-13-328-41-780 20 1.0 0.4 0.5 20 104-13-420-41-770 104-13-420-41-780 22 1.1 0.4 0.5 18 104-13-422-41-770 104-13-422-41-780 24 1.2 0.4 0.5 16 104-13-424-41-770 104-13-424-41-780 28 1.4 0.4 0.5 14 104-13-428-41-770 104-13-428-41-780 32 1.6 0.4 0.5 12 104-13-432-41-770 104-13-432-41-780 24 1.2 0.6 0.7 16 104-13-624-41-770 104-13-624-41-780 28 1.4 0.6 0.7 14 104-13-628-41-770 104-13-628-41-780 32 1.6 0.6 0.7 12 104-13-632-41-770 104-13-632-41-780 36 1.8 0.6 0.7 11 104-13-636-41-770 104-13-636-41-780 40 2.0 0.6 0.7 10 104-13-640-41-770 104-13-640-41-780 42 2.1 0.6 0.7 9 104-13-642-41-770 104-13-642-41-780 48 2.4 0.6 0.7 8 104-13-648-41-770 104-13-648-41-780 50 2.5 0.6 0.7 8 104-13-650-41-770 104-13-650-41-780 52 2.6 0.6 0.7 7 104-13-652-41-770 104-13-652-41-780 50 2.5 0.9 1.0 8 104-13-950-41-770 104-13-950-41-780 52 2.6 0.9 1.0 7 104-13-952-41-770 104-13-952-41-780 64 3.2 0.9 1.0 6 104-13-964-41-770 104-13-964-41-780 plating code = 13 sleeve (pin) contact (clip) 10 ? au 30 ? au for high temperature insulators add ?100? to end of part numbers total number of pins quantity per tube ordering information a b c l = .175 l = .250 (for .062 thick panel) (for .125 thick panel) ? designed for solderless press-fit into plated-thru holes. ? pin lengths are suitable for .062? and .093?-.125? thick panels. ? required plated thru-hole is .036?-.041?, ie: use a 1.1mm drill prior to plating. ? uses m-m# 0477 or 0478 with #30 contact, rated for 3 amps. see page 131 for pin details.
|